Introduction to 8086 Microprocessor ppt - م.م. عمر صلاح

Introduction to 8086 Microprocessor

Electronics Engineering college Communication Dep. 3rd class Lecture 2

Architecture of 8086

The architecture of 8086 includes Arithmetic Logic Unit (ALU) Flags General registers Instruction byte queue Segment registers

EU & BIU

The 8086 CPU logic has been partitioned into two functional units namely Bus Interface Unit (BIU) and Execution Unit (EU) The major reason for this separation is to increase the processing speed of the processor The BIU has to interact with memory and input and output devices in fetching the instructions and data required by the EU EU is responsible for executing the instructions of the programs and to carry out the required processing

EU & BIU

Architecture Diagram

Execution Unit

The Execution Unit (EU) has Control unit Instruction decoder Arithmetic and Logical Unit (ALU) General registers Flag register Pointers Index registers

Execution Unit

Control unit is responsible for the co-ordination (control) of all other units of the processor ALU performs various arithmetic and logical operations over the data The instruction decoder translates the instructions fetched from the memory into a series of actions that are carried out by the EU

Execution Unit - Registers
General registers are used for temporary storage and manipulation of data and instructions Accumulator register consists of two 8-bit registers AL and AH, which can be combined together and used as a 16-bit register AX Accumulator can be used for I/O operations and string manipulation

Execution Unit - Registers

Base register consists of two 8-bit registers BL and BH, which can be combined together and used as a 16-bit register BX BX register usually contains a data pointer used for based, based indexed or register indirect addressing Count register consists of two 8-bit registers CL and CH, which can be combined together and used as a 16-bit register CX Count register can be used as a counter in string manipulation and shift/rotate instructions

Execution Unit - Registers

Data register consists of two 8-bit registers DL and DH, which can be combined together and used as a 16-bit register DX Data register can be used as a port number in I/O operations In integer 32-bit multiply and divide instruction the DX register contains high-order word of the initial or resulting number

Execution Unit - Registers

Execution Unit - Flags

Overflow Flag (OF) - set if the result is too large positive number, or is too small negative number to fit into destination operand Direction Flag (DF) - if set then string manipulation instructions will auto-decrement index registers. If cleared then the index registers will be auto-incremented Interrupt-enable Flag (IF) - setting this bit enables maskable interrupts Single-step Flag (TF) - if set then single-step interrupt will occur after the next instruction

Execution Unit - Flags
Sign Flag (SF) - set if the most significant bit of the result is set. Zero Flag (ZF) - set if the result is zero. Auxiliary carry Flag (AF) - set if there was a carry from or borrow to bits 0-3 in the AL register. Parity Flag (PF) - set if parity (the number of "1" bits) in the low-order byte of the result is even. Carry Flag (CF) - set if there was a carry from or borrow to the most significant bit during last result calculation

Execution Unit - Flags

Execution Unit - Pointers
Stack Pointer (SP) is a 16-bit register pointing to program stack Base Pointer (BP) is a 16-bit register pointing to data in stack segment. BP register is usually used for based, based indexed or register indirect addressing. Source Index (SI) is a 16-bit register. SI is used for indexed, based indexed and register indirect addressing, as well as a source data addresses in string manipulation instructions. Destination Index (DI) is a 16-bit register. DI is used for indexed, based indexed and register indirect addressing, as well as a destination data addresses in string manipulation instructions.

Execution Unit - Pointers

Bus Interface Unit
The BIU has Instruction stream byte queue A set of segment registers Instruction pointer

BIU – Instruction Byte Queue 8086 instructions vary from 1 to 6 bytes Therefore fetch and execution are taking place concurrently in order to improve the performance of the microprocessor The BIU feeds the instruction stream to the execution unit through a 6 byte prefetch queue This prefetch queue can be considered as a form of loosely coupled pipelining

BIU – Instruction Byte Queue Execution and decoding of certain instructions do not require the use of buses While such instructions are executed, the BIU fetches up to six instruction bytes for the following instructions (the subsequent instructions) The BIU store these prefetched bytes in a first-in-first out register by name instruction byte queue When the EU is ready for its next instruction, it simply reads the instruction byte(s) for the instruction from the queue in BIU

Segment: Offset Notation

The total addressable memory size is 1MB Most of the processor instructions use 16-bit pointers the processor can effectively address only 64 KB of memory To access memory outside of 64 KB the CPU uses special segment registers to specify where the code, stack and data 64 KB segments are positioned within 1 MB of memory

Segment: Offset Notation
A simple scheme would be to order the bytes in a serial fashion and number them from 0 (or 1) to the end of memory The scheme used in the 8086 is called segmentation Every address has two parts, a SEGMENT and an OFFSET (Segmnet:Offset ) The segment indicates the starting of a 64 kilobyte portion of memory, in multiples of 16 The offset indicates the position within the 64k portion Absolute address = (segment * 16) + offset

Segment Registers

The memory of 8086 is divided into 4 segments namely Code segment (program memory) Data segment (data memory) Stack memory (stack segment) Extra memory (extra segment)

Different Areas in Memory

Program memory – Program can be located anywhere in memoryData memory – The processor can access data in any one out of 4 available segments Stack memory – A stack is a section of the memory set aside to store addresses and data while a subprogram executes Extra segment – This segment is also similar to data memory where additional data may be stored and maintained

Segment Registers

Code Segment (CS) register is a 16-bit register containing address of 64 KB segment with processor instructions The processor uses CS segment for all accesses to instructions referenced by instruction pointer (IP) register Stack Segment (SS) register is a 16-bit register containing address of 64KB segment with program stack By default, the processor assumes that all data referenced by the stack pointer (SP) and base pointer (BP) registers is located in the stack segment

Segment Registers

Data Segment (DS) register is a 16-bit register containing address of 64KB segment with program data By default, the processor assumes that all data referenced by general registers (AX, BX, CX, DX) and index register (SI, DI) is located in the data segment Extra Segment (ES) register is a 16-bit register containing address of 64KB segment, usually with program data By default, the processor assumes that the DI register references the ES segment in string manipulation instructions

Segment Registers

Pin Diagram

Addressing Modes
Implied Addressing – The data value/data address is implicitly associated with the instructionRegister Addressing – The data is specified by referring the register or the register pair in which the data is present Immediate Addressing – The data itself is provided in the instruction Direct Addressing – The instruction operand specifies the memory address where data is located

Addressing Modes

Register indirect addressing – The instruction specifies a register containing an address, where data is located Based - 8-bit or 16-bit instruction operand is added to the contents of a base register (BX or BP), the resulting value is a pointer to location where data residesIndexed - 8-bit or 16-bit instruction operand is added to the contents of an index register (SI or DI), the resulting value is a pointer to location where data resides

Addressing Modes

Based Indexed - the contents of a base register (BX or BP) is added to the contents of an index register (SI or DI), the resulting value is a pointer to location where data resides Based Indexed with displacement - 8-bit or 16-bit instruction operand is added to the contents of a base register (BX or BP) and index register (SI or DI), the resulting value is a pointer to location where data resides

Introduction to 8086 Microprocessor